Loctite SF 7070 Odc-free Cleaner& Degreaser

0.0

Description

Loctite SF 7070 Odc-free Cleaner & degreaser

  • Viscosity : Very Low
  • Colour : Transparent
  • Curing Type : Not applicable
  • Application : Surface cleaner
 

LOCTITE SF 7070 is a solvent-based (non-CFC) parts cleaner and degreaser formulated specifically to prepare plastic components ready for bonding with adhesives. Suitable for use as a spray or in immersion cleaning at room temperature, the product is able to remove most oils, greases, lubrication fluids, metal cuttings and fines from plastic parts without the risk of stress cracks.

  • Solvent-based general parts cleaner
  • Designed for use on plastic components
  • Can be applied by spray or immersion
  • No risk of stress cracks
LOCTITE® SF 7070™ is a non-aqueous, hydrocarbon based,
non-CFC solvent designed for cleaning and degreasing of
surfaces to be bonded with LOCTITE®
adhesives. The product
is used as a final pre-assembly cleaning treatment to remove
most greases, oils, lubrication fluids, metal cuttings and fines
from surfaces to be bonded. It is designed to be used as a
spray or in immersion cleaning processes at room temperature
or heated.
NSF International

Registered to NSF Category K1 for use as a cleaner and
degreaser in non food processing areas which are used to
remove oil, wax, resinous materials, or other substances not
removable by using acidic or alkaline cleaning agents. Note:
This is a regional approval. Please contact your local Technical
Service Center for more information and clarification.
TYPICAL PERFORMANCE

LOCTITE® SF 7070™ has no effect on the speed of cure or
final strength of LOCTITE®
adhesives other than providing a
clean surface for good adhesion and adhesive cure. Unclean
or partially cleaned surfaces can affect adhesive performance.
Handling precautions

Cleaner must be handled in a manner applicable to highly
flammable materials and in compliance with relevant local
regulations.
Special care must be taken to avoid contact of the product or
its vapour with naked flame or any electrical equipment that is
not flame proofed.
The solvent can affect certain plastics or coatings. It is
recommended to check all surfaces for compatibility before
use.
LOCTITE® SF 7070™ is compatible with metals, many plastics
and elastomers.
The following table shows the effect of LOCTITE® SF 7070™
on various plastics and elastomers. Since compatibility is
affected by material variation, it is recommended to check parts
and cleaning equipment gaskets, seals and O-rings under end
use conditions before adopting use of LOCTITE® SF 7070™.
GENERAL INFORMATION

This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
Directions for use:


  1. Treat surfaces to be cleaned by spraying or wiping surfaces with
    a solvent soaked paper towel.
  2. Wipe surfaces when still wet with a clean cloth to remove all
    heavy contamination. If necessary, spray surfaces again to allow
    run-off of product.
  3. Repeat cleaning process if necessary.
  4. Allow LOCTITE® SF 7070™ to fully evaporate from parts prior to
    bonding to avoid solvent entrapment within the bond joint.
  5. Apply the Loctite®
    adhesive immediately after drying and
    assemble bond

Loctite Material Specification

LMS dated March-23, 2005. Test reports for each batch are available
for the indicated properties. LMS test reports include selected QC test
parameters considered appropriate to specifications for customer use.
Additionally, comprehensive controls are in place to assure product
quality and consistency. Special customer specification requirements
may be coordinated through Henkel Quality
Storage

Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Read More Read Less
Products dan Cleaner / Remover

Categories

Loctite

Products Brand

You may also like