Loctite Ea 9462 Epoxy Adhesive 50ml

0.0

Description

Loctite Ea 9462 Epoxy Adhesive 50ml

  • Strength : High
  • Color : Neutral
  • Curing Type : Heat Cure, Room Temperature (Ambient) Cure
  • Application : Bonding
 

LOCTITE® EA 9462 is a beige, 2-part, toughened, epoxy adhesive paste formulated for a good balance of shear and peel properties with ease of use. Its medium viscosity, 1:1 ratio and non-sag features make it easy to apply. Recommended substrates are metals, plastics and wood.

  • Excellent strength
  • Impact resistant
  • Non-sag
  • Room temperature or heat cure
  • Neutral color
LOCTITE® EA 9462 is a toughened, two component epoxy adhesive
formulated for a good balance of shear and peel properties in an easy
to use, smooth paste. Its medium viscosity, 1:1 ratio and non-sag
features make it easy to apply.
Recommend Substrates: metals, plastics and wood.
GENERAL INFORMATION

This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
Handling

Mixing: This product requires mixing two components together just
prior to the application. Complete mixing is necessary. The
temperature of the separate components prior to mixing is not critical,
but they should be at room temperature.
Application

Mixing – Bulk: Combine Part A (resin) and Part B (hardener) in the
correct ratio and mix thoroughly until the color and consistency are
uniform. Ratios given above can be used for measuring larger
amounts. Mixing the adhesive just prior to use is recommended. Heat
build-up during or after mixing is normal. Do not mix quantities greater
than two pounds as dangerous heat build-up can occur causing
uncontrolled decomposition of the mixed adhesive. Mixing smaller
quantities will minimize the heat build-up.

Mixing – Cartridges: Place cartridge in proper dispenser. To begin
using a new cartridge, remove cartridge cap and dispense a small
amount of adhesive, making sure Part A and Part B are extruding.
Attach nozzle and dispense approximately 1-2” before applying onto
the part being bonded. Partially used cartridges can be stored with
mixing nozzle attached. To reuse, remove and discard the old nozzle,
attach new nozzle and begin dispensing.


Application: Bonding surfaces should be clean and dry. Once the
adhesive is applied, the boned parts should beheld in contact until the
part has developed handling strength. This will occur in 4-8 hours at
77 oF after which the pressure used during cure may be removed.
Since full bond has not yet been attained, load application should be
small at this time. It is not necessary to clamp the parts unless
movement during curing is likely.


Cure: LOCTITE® EA 9462 may be cured for 3-5 days at 77 oF to
achieve normal performance. Accelerated cures up to 200 oF (for
small masses only) may be used as an alternative. For example 1
hour at 180 oF will give complete cure.


Clean up: It is important to remove excess adhesive from the work
area and application equipment before it hardens. Many common
solvents and citrus cleaners are suitable for removing uncured
adhesive. Consult with your supplier’s information pertaining to the
safe and proper use of solvents.


Storage

Store product in unopened container in a cool dry location. Ideal
conditions are within the range 8 to 21 degrees C (46 to 70
degrees F) and are recommended for long term storage.
Exposure to higher temperatures (greater than 28 degrees C) for
prolonged periods should be avoided as extended exposure to
warm conditions can adversely affect product properties. For
further specific shelf life information, contact your local Technical
Service Center.


 
Read More Read Less
Products dan Adhesive / Sealant

Categories

Loctite

Products Brand

You may also like