Teroson Ms 9360 Polymer Solvent-free Sealant Adhesive Black 310g
Description
component adhesive based on silane modified polymer,
which cures to an elastic product. The skin formation and
curing times are dependent on humidity and temperature, and
the curing time also depends on joint depth. By increasing the
temperature and moisture these times can be reduced;low
temperature as well as low moisture retard the process.
Teroson MS 9360 is free of solvents, isocyanates, silicones
and PVC. It demonstrates good adhesion to many substrates.
The sealant also demonstrates good UV resistance and can
therefore be used for interior and exterior applications.
Teroson MS 9360 allows accelerated curing as
two-component material
Teroson MS 9360 is used for elastic bonding on metallic or
painted substrates as well as for adhesive sealings of all kind.
After matching of the materials to be bonded a high position
tack is obtained.
Prior to application it is necessary to read the Material Safety
Data Sheet for information about precautionary measures
and safety recommendations. Also, for chemical products
exempt from compulsory labeling, the relevant precautions
should always be observed.
The substrates must be clean, dry, oil- and grease free. Depending
on the surface it can be necessary to roughen the surface or to use a
primer/adhesion promoter to provide best adhesion. When
manufacturing plastics, external release agents are often used; these
agents must be accurately removed prior to starting bonding or
sealing. Due to the different compositions of paints, especially
powder paints and the large number of different substrates,
application trials before use are necessary. For cleaning, Cleaner +
Diluent A, FL or Teroson SB 450 from the Henkel portfolio are
suitable. When bonding and sealing PMMA, e.g. Plexiglas®, and
polycarbonate, e.g. Makrolon® or Lexan®, under tension, stress
corrosion cracking may occur. Application trials before use are
necessary. There is no adhesion to polyethylene, polypropylene and
PTFE (e.g. Teflon®). Substrates not mentioned above should be
subject to trials.
Application from 290 ml cartridges is made with the Teroson Hand or
Air Pressure Pistols, and from plastic wallets (310 and 570 ml) with
the corresponding FK-Hand or FK-Air Pressure Pistols. In the case of
compressed air application a pressure of 2 to 5 bar is required. Low
material temperatures of the sealant will lead to an increase of
viscosity, resulting in a lower extrusion rate. This can be avoided by
bringing the sealant up to room temperature prior to application.
Teroson MS 9360 can also be applied from hobbocks or drums with
high pressure pumps with follower plates. See separate application
directions of Teroson MS products in hobbocks and drums.
For cleaning application equipment contaminated with
uncured Teroson MS 9360 we recommend the use of
Cleaner+Diluent Teroson A, D or FL.
Read More
Read Less
Teroson Ms 9360 Polymer Solvent-free Sealant Adhesive Black 310g
- Tensile Strength : 3.5 MPa
- Color : Black
- Curing Type : Humidity
- Application : Assembly
- High strength
- Free of solvents
- odorless
- Compatible with paint systems
component adhesive based on silane modified polymer,
which cures to an elastic product. The skin formation and
curing times are dependent on humidity and temperature, and
the curing time also depends on joint depth. By increasing the
temperature and moisture these times can be reduced;low
temperature as well as low moisture retard the process.
Teroson MS 9360 is free of solvents, isocyanates, silicones
and PVC. It demonstrates good adhesion to many substrates.
The sealant also demonstrates good UV resistance and can
therefore be used for interior and exterior applications.
Teroson MS 9360 allows accelerated curing as
two-component material
Application Areas:
Teroson MS 9360 is used for elastic bonding on metallic or
painted substrates as well as for adhesive sealings of all kind.
After matching of the materials to be bonded a high position
tack is obtained.
DIRECTIONS OF USE
Preliminary statement:
Prior to application it is necessary to read the Material Safety
Data Sheet for information about precautionary measures
and safety recommendations. Also, for chemical products
exempt from compulsory labeling, the relevant precautions
should always be observed.
Pre-Treatment:
The substrates must be clean, dry, oil- and grease free. Depending
on the surface it can be necessary to roughen the surface or to use a
primer/adhesion promoter to provide best adhesion. When
manufacturing plastics, external release agents are often used; these
agents must be accurately removed prior to starting bonding or
sealing. Due to the different compositions of paints, especially
powder paints and the large number of different substrates,
application trials before use are necessary. For cleaning, Cleaner +
Diluent A, FL or Teroson SB 450 from the Henkel portfolio are
suitable. When bonding and sealing PMMA, e.g. Plexiglas®, and
polycarbonate, e.g. Makrolon® or Lexan®, under tension, stress
corrosion cracking may occur. Application trials before use are
necessary. There is no adhesion to polyethylene, polypropylene and
PTFE (e.g. Teflon®). Substrates not mentioned above should be
subject to trials.
Application:
Application from 290 ml cartridges is made with the Teroson Hand or
Air Pressure Pistols, and from plastic wallets (310 and 570 ml) with
the corresponding FK-Hand or FK-Air Pressure Pistols. In the case of
compressed air application a pressure of 2 to 5 bar is required. Low
material temperatures of the sealant will lead to an increase of
viscosity, resulting in a lower extrusion rate. This can be avoided by
bringing the sealant up to room temperature prior to application.
Teroson MS 9360 can also be applied from hobbocks or drums with
high pressure pumps with follower plates. See separate application
directions of Teroson MS products in hobbocks and drums.
Cleaning:
For cleaning application equipment contaminated with
uncured Teroson MS 9360 we recommend the use of
Cleaner+Diluent Teroson A, D or FL.
Teroson Ms 9360 Polymer Solvent-free Sealant Adhesive Black 310g
Sale price$0.00
Regular price (/)
Products and Adhesive / Sealant
Categories
Loctite
Products Brand
This product has no reviews yet.
