Permatex Ultra Blue Rtv Silicone Gasket Maker 13oz
Description
Permatex Ultra Blue RTV Silicone Gasket is a single
component, room temperature vulcanizing gasketing
compound designed to provide reliable “formed-in-place”
gaskets for mechanical assemblies. This material cures on
exposure to moisture in the air to form a tough, flexible,
silicone rubber gasket. The product resists aging, weathering
and thermal cycling without hardening, shrinking or cracking.
Designed for superior bonding properties to oil contaminated
metals as compared to other formed-in-place gaskets, and
maintains outstanding oil resistance. NSF White Book
registered.
For assembly as form-in-place gasket
For assembly as gasket dressing
Note: Product not recommended for use as a cylinder
head gasket or head gasket sealant
Permatex Ultra Blue No-Leak RTV Silicone Gasket cures on
exposure to moisture in the air. The product dries tack free in
two hours and fully cures in 24 hours. Cure times will vary
with temperature, humidity and gap.
The product retains effective properties in contact with
automotive fluids, such as motor oil, transmission fluids,
alcohol and antifreeze solutions. Note: Not recommended for
parts in contact with gasoline.
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8 to 28C
(46 to 82F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused products, do not return any material to
its original container.
TDS
SDS
Read More
Read Less
Permatex Ultra Blue Rtv Silicone Gasket Maker 13oz
Permatex Ultra Blue RTV Silicone Gasket is a single
component, room temperature vulcanizing gasketing
compound designed to provide reliable “formed-in-place”
gaskets for mechanical assemblies. This material cures on
exposure to moisture in the air to form a tough, flexible,
silicone rubber gasket. The product resists aging, weathering
and thermal cycling without hardening, shrinking or cracking.
Designed for superior bonding properties to oil contaminated
metals as compared to other formed-in-place gaskets, and
maintains outstanding oil resistance. NSF White Book
registered.
PRODUCT BENEFITS
- Sensor safe, non-corrosive
- Superior adhesion and flexibility
- Improved oil resistance
- Replaces most cut gaskets
- Low odor
- Can be used as a gasket maker or dressing
- Non-flammable, Non-toxic
TYPICAL APPLICATIONS
- Pump housings
- Machine tools
- Compressors
- Gearboxes
- Transmission pans
- Valve covers
- Oil pans
DIRECTIONS FOR USE
For assembly as form-in-place gasket
- Remove all previous material from mating surfaces.
Permatex Gasket Remover is recommended for most
materials. - For best results, clean and dry all surfaces with a
residue-free solvent, such as Permatex Brake and
Parts Cleaner. - Cut nozzle to desired bead size, 1/16“ to 1/4“ in
diameter. A 1/8” bead is usually sufficient for most
applications. - Remove cap, puncture tube or cartridge seal and attach
extension nozzle. - Apply a continuous 1/16 inch to 1/8 inch bead of silicone
to one surface, first tracing the internal areas of the
gasket configuration, then all surrounding bolt holes. - Assemble parts immediately while silicone is still wet.
- Finger tighten flange only until material begins to seep
out the sides of the flange. - Allow to set for at least two hours and re-torque at lease
one quarter to one half turn. - For best results, allow to cure overnight
For assembly as gasket dressing
- Repeat steps 1 thru 4 as in previous section.
- Apply a thin film of silicone to one surface to be sealed.
- Place the pre-cut gasket onto silicone film.
- Apply a second thin film to pre-cut gasket surface.
- Remove any excess and assemble parts immediately
Note: Product not recommended for use as a cylinder
head gasket or head gasket sealant
Instructions for PowerBead
- Clean and dry all flange surfaces to be sealed.
- Remove black cap from top of extension nozzle.
- Turn nozzle extension one complete turn (360)
counterclockwise. - Depress finger trigger and apply a continuous 1/16 inch
to 1/8 inch PowerBead to one surface. - Assemble parts immediately while silicone is still wet.
- Finger tighten flange only until material begins to seep
out the sides of the flange. - Allow to set for at least two hours and re-torque at least
one quarter to one half turn. - For best results, allow to cure overnight.
- To close, turn extension nozzle clockwise until tight
(about one full turn). Wipe off excess material from
nozzle and replace black cap.
For Cleanup
- Remove uncured product from parts and hand-tools with
Permatex® Fast Orange® Wipes or Fast Orange® Hand
Cleaners. If skinned over, break film with a dry cloth to
remove as much as possible. Remove the remaining
material with Permatex® Gasket Remover. - Clean hands with a dry cloth or Permatex Fast Orange
hand cleaner.
Storage of Unused Product
- Create a “Silicone Plug” by allowing excess material to
extend beyond the extension nozzle or aerosol tip to
cure, sealing and protecting the remaining product from
moisture. For reuse, simply remove the cured product
from the tip. - For PowerBead dispensers, you may store remaining
product using either the above “silicone plug” method or
using the included plastic cap.
TYPICAL CURING PERFORMANCE
Permatex Ultra Blue No-Leak RTV Silicone Gasket cures on
exposure to moisture in the air. The product dries tack free in
two hours and fully cures in 24 hours. Cure times will vary
with temperature, humidity and gap.
Chemical / Solvent Resistance
The product retains effective properties in contact with
automotive fluids, such as motor oil, transmission fluids,
alcohol and antifreeze solutions. Note: Not recommended for
parts in contact with gasoline.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8 to 28C
(46 to 82F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused products, do not return any material to
its original container.
TDS
SDS
Permatex Ultra Blue Rtv Silicone Gasket Maker 13oz
Sale price$0.00
Regular price (/)
Products and Cleaner / Remover
Categories
Permatex
Products Brand