Permatex 82180 Ultra Black RTV Silicone Gasket 85g

Permatex 82180 Ultra Black Oil Resistance Rtv Silicone Gasket Maker 85g

Permatex Ultra Black Gasket Maker is a single component,
room temperature, vulcanizing, gasketing compound designed
to provide reliable “formed-in-place” gaskets for mechanical
assemblies. This material cures on exposure to moisture in
the air to form a tough, flexible, silicone rubber gasket. The
product resists aging, weathering and thermal cycling without
hardening, shrinking or cracking. Designed to provide
increased oil resistance and complies with extended warranty
requirements. OEM Specified.

PRODUCT BENEFITS

• Improved oil resistance
• Sensor safe, non-corrosive
• Good adhesion and flexibility
• Replaces most cut gaskets
• Can be used as a gasket maker or dressing
• Non-flammable, Non-toxic
• Low odor

TYPICAL APPLICATIONS

• Oil pans
• Transmission pans
• Valve covers
• Valves and guides
• Timing gear covers
• Differential covers

DIRECTIONS FOR USE

For assembly as a form-in-place gasket

1. Remove all previous material from mating surfaces.
   Permatex® Gasket Remover is recommended for most
   materials, not for plastics or painted surfaces.
2. For best results, clean and dry all surfaces with a
   residue-free solvent, such as Permatex® Brake and
   Parts Cleaner
3. Cut nozzle to desired bead size, 1/16” to 1/4” in
   diameter. A 1/8” bead is usually sufficient for most
   applications.
4. Remove cap, puncture tube or cartridge seal and attach
   extension nozzle.
5. Apply a continuous and even bead of silicone to one
   surface, first tracing the internal areas of the gasket
   configuration, then all surrounding bolt holes
6. Assemble parts immediately while silicone is still wet.
7. Finger tighten flange only until material begins to seep
   out the sides of the flange.
8. Allow to set for at least two hours and re-torque at least
   one quarter to one half turn.
9. For best results, allow to cure overnight.

For assembly as a gasket dressing

1. Repeat steps 1 through 4 as in previous section.
2. Apply a thin film of silicone to one surface to be sealed.
3. Place the pre-cut gasket onto silicone film.
4. Apply a second thin film to pre-cut gasket surface.
5. Remove any excess and assemble parts immediately.

Note: Product is not recommended for use as a cylinder
head gasket or head gasket sealant.

Instructions for PowerBead

1. Clean and dry all flange surfaces to be sealed.
2. Remove black cap from top of extension nozzle.
3. Turn nozzle extension one complete turn (360)
   counterclockwise.
4. Depress finger trigger and apply a continuous 1/16 inch
   to 1/8 inch PowerBead to one surface.
5. Assemble parts immediately while silicone is still wet.
6. Finger tighten flange only until material begins to seep
   out the sides of the flange.
7. Allow to set for at least two hours and re-torque at least
   one quarter to one half turn.
8. For best results, allow to cure overnight.
9. To close, turn extension nozzle clockwise until tight
   (about one full turn). Wipe off excess material from
   nozzle and replace black cap.

Storage of Unused Product

1. Create a “Silicone Plug” by allowing excess material to
   extend beyond the extension nozzle or aerosol tip to
   cure, sealing and protecting the remaining product from
   moisture. For reuse, simply remove the cured product
   from the tip.
2. For PowerBead dispensers, you may store remaining
   product using either the above “silicone plug” method or
   using the included plastic cap.

For Cleanup

1. Remove uncured product from parts and hand-tools with
   Permatex® Fast Orange® Wipes or Fast Orange® Hand
   Cleaners. If skinned over, break film with a dry cloth to
   remove as much as possible. Remove the remaining
   material with Permatex® Gasket Remover.
2. Clean hands with a dry cloth or Permatex® Fast
   Orange Hand Cleaner.

TYPICAL CURING PERFORMANCE

Permatex Ultra Black Gasket Maker cures on exposure to
moisture in the air. The product dries tack free in two hours
and fully cures in 24 hours. Cure times will vary with
temperature, humidity and gap.

Chemical / Solvent Resistance

The product retains effective properties in contact with
automotive fluids, such as motor oil, transmission fluids,
alcohol and antifreeze solutions. Note: Not recommended for
parts in contact with gasoline.

GENERAL INFORMATION

This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).

STORAGE

Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8 and 28C
(46 and 82F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.