Loctite SF 7063 Super Clean
Description
for cleaning and degreasing of surfaces to be bonded with
LOCTITE®
adhesives. The product can also be used for
cleaning and degreasing machine components during
maintenance operations.
LOCTITE® SF 7063™ has no effect on the speed of cure or
final strength of LOCTITE®
adhesives other than providing a
clean surface for good adhesion and adhesive cure. Unclean
or partially cleaned surfaces can affect adhesive performance
Cleaner must be handled in a manner applicable to highly
flammable materials and in compliance with relevant local
regulations.
Special care must be taken to avoid contact of the product or
its vapour with naked flame or any electrical equipment that is
not flame proofed.
The solvent can affect certain plastics or coatings. It is
recommended to check all surfaces for compatibility before
use.
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
LMS dated December-01, 2004. Test reports for each batch
are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Read More
Read Less
Loctite SF7063 Super Clean 400ml
- Viscosity : Very Low
- Colour : Transparent
- Curing Type : Not applicable
- Application : Surface cleaner
LOCTITE SF 7063 is our general-purpose product for cleaning and degreasing any kind of surface or machinery component before proceeding with a repair or assembly job involving LOCTITE® adhesives. It is a solvent-based cleaner and the product leaves no residue. LOCTITE 7063 removes most greases, oils, lubrication fluids and metal cuttings.
- Solvent-based general parts cleaner
- Ideal for use prior to adhesive bonding and sealing applications
- Leaves no residue
- Removal of most greases, oils, lubrication fluids, metal cuttings and fines from all surfaces
for cleaning and degreasing of surfaces to be bonded with
LOCTITE®
adhesives. The product can also be used for
cleaning and degreasing machine components during
maintenance operations.
TYPICAL PERFORMANCE
LOCTITE® SF 7063™ has no effect on the speed of cure or
final strength of LOCTITE®
adhesives other than providing a
clean surface for good adhesion and adhesive cure. Unclean
or partially cleaned surfaces can affect adhesive performance
Handling precautions
Cleaner must be handled in a manner applicable to highly
flammable materials and in compliance with relevant local
regulations.
Special care must be taken to avoid contact of the product or
its vapour with naked flame or any electrical equipment that is
not flame proofed.
The solvent can affect certain plastics or coatings. It is
recommended to check all surfaces for compatibility before
use.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
Directions for use:
- Treat surfaces to be cleaned by spraying or wiping
surfaces with a solvent soaked paper towel. - Wipe surfaces when still wet with a clean cloth to remove
all heavy contamination. If necessary, spray surfaces
again to allow run-off of product. - Repeat cleaning process if necessary.
- Allow LOCTITE® SF 7063™ to fully evaporate from parts
prior to bonding to avoid solvent entrapment within the
bond joint. - Apply the Loctite®
adhesive immediately after drying and
assemble bond.
Loctite Material Specification
LMS dated December-01, 2004. Test reports for each batch
are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Loctite SF 7063 Super Clean
Sale price$0.00
Regular price (/)
Products and Cleaner / Remover
Categories
Loctite
Products Brand