Devcon Brushable Ceramic White



Devcon Brushable Ceramic White

A brushable, high-performance, ceramic-filled epoxy for sealing, protecting, and repairing surfaces subject to erosion,
corrosion, and wear

Intended Use:

Protect pump casings, impeller blades, gate valves, water boxes, and fan blades; rebuild heat exchangers, tube sheets,
and other water circulating equipment; top coat on repaired surfaces; seal and protect new equipment exposed to erosion
and corrosion
  • Excellent chemical resistance
  • Temperature resistance to 350°F
  • Applies easily with short-bristle brush or roller
  • Low viscosity, self-leveling liquid
  • Acceptable for use in meat and poultry plants
  • NSF® Approved (Certified to ANSI/NSF61)
  • chemical resistance coating
  • Repair coating
  • Chemical coating
Surface Preparation

  1. Thoroughly clean the surface with Devcon® Cleaner Blend 300 to remove all oil, grease and dirt.
  2. Grit blast surface area with 8-40 mesh grit, or grind with a coarse wheel or abrasive disc pad, to create increased
    surface area for better adhesion (Caution: An abrasive disc pad can only be used provided white metal is revealed).
    Desired profile is 3-5mil, including defined edges (do not "feather-edge” epoxy).Note: For metals exposed to sea water or other salt solution, grit-blast and high-pressure-water-blast the area, then leave
    overnight to allow any salts in the metal to “sweat” to the surface. Repeat blasting to “sweat out” all soluble salts. Perform
    chloride contamination test to determine soluble salt content (should be no more than 40ppm).
  3. Clean surface again with Devcon® Cleaner Blend 300 to remove all traces of oil, grease, dust or other foreign
    substances from the grit blasting.
  4. Repair surface as soon as possible to eliminate any changes or surface contaminants.WORKING CONDITIONS: Ideal application temperature is 55°F to 90°F. In cold working conditions, directly heat repair
    area to100-110°F prior to applying epoxy and maintain at this temperature during product cure to dry off any moisture,
    contamination or solvents, as well as to achieve maximum performance properties.


---- It is strongly recommended that full units be mixed, as ratios are pre-measured. ----

  1. Add hardener to resin
  2. Mix thoroughly with screwdriver or similar tool (continuously scrape material away from sides and bottom of container)
    until a uniform, streak-free consistency is obtained.

LARGE SIZES (3 lb, 4 lb, 25 lb): Use a propeller-type Jiffy Mixer on an electric drill. Use model HS-1 for 3 lb and 4 lb kits.
Use model ES for 25 lb kit. Mix until color is uniform and consistent.
Note: Keep propeller below liquid line, as additional air can be added to mixture, resulting in air bubbles on the surface of
the finished product.

Apply two thin coats (8-15 mils) of Brushable Ceramic to ensure a lack of pinholes or holidays on the substrate (a low
voltage, holiday detector will ensure a pinhole-free coating). Brushable Ceramic fully cures in 16 hours, at which time it
can be machined, drilled or painted.
    Use Brushable Ceramic as a coating in combination with Ceramic Repair Putty. For proper wear and adhesion, maximum
    thickness should not exceed 40 mils.
    Applying epoxy at temperatures below 70°F lengthens functional cure and pot life times. Conversely, applying above 70°F
    shortens functional cure and pot life.

Store at room temperature, 70 °F.

NSF-certified for potable water applications For NSF certification a cure time of 7 days is required.
Approved for use in meat and poultry processing plants

ITW Performance Polymers will replace any material found to be defective. Because the storage, handling and
application of this material is beyond our control, we can accept no liability for the results obtained.
These are the frequently asked questions :
What is chemical resistance material?
Is powder coating chemical resistant?
What material has the best chemical resistance?
Belzona 4331 Chemical resistant coating
Feel free to contact us if there are any queries above or other questions we will be glad to assist you. Demo Practices are available too, we have our professional to guide you or recommend proper application on the products.

Read more about devcon products

Distributor for devcon in South East Asia
Devcon Distributor for Singapore
Devcon Distributor for  Cambodia
Devcon Distributor for Brunei
Devcon Distributor for Cambodia
Devcon Distributor for Myanmar
Largest Stockist for devcon products.
Read More Read Less
ProductsและAdhesive / Sealant



Products Brand

You may also like