Permatex High Performance Thread Sealant 10000 PSI

Permatex High Performance Thread Sealant 10000 PSI

Permatex High Performance Thread Sealant is formulated for
fast, responsive curing on metal pipe threads and fittings. This
sealant is a smooth, white paste-like compound with PTFE
that controls lubricity to assist assembly and torque tightening.
Permatex High Performance Thread Sealant replaces tape or
pipe dopes. It cures rapidly to withstand 10,000 PSI within 24
hours. Prevents galling and protects mated threaded
surfaces from rust and corrosion. The product cures when
confined in the absence of air between close fitting metal
surfaces. This product is not recommended for use on
plastic piping. NSF White Book registered.

PRODUCT BENEFITS

• Quick fixture time
• Prevents galling and corrosion
• Controlled strength
• Temperature and solvent resistance
• Immediate low pressure sealing
• Contains PTFE

TYPICAL APPLICATIONS

Recommended for sealing metal tapered pipe threads and
fittings up to 5cm (2 inches) National Pipe Thread (NPT) for
industrial applications in the chemical processing, petroleum
refining, pulp/paper, waste treatment, textile, utilities/power
generation, marine, automotive, industrial equipment, gas
compression and distribution industries. It is also
recommended for industrial plant fluid power systems

• Stainless steel fittings
• Head bolts into through holes
• Oil PSI sending units/sensors
• Fuel fittings
• Oil and coolant lines
• Hydraulic line fittings
• Brake fittings
• Transmission fluid fittings
• PTO fittings
• Air conditioning fittings

DIRECTIONS FOR USE

1. For best performance, surfaces should be clean and free
   of grease.
2. Product should be applied to the thread engagement
   area in sufficient quantity to fill all engaged threads.
3. Use accepted trade practices to assemble and wrenchtighten
   fittings until proper alignment is obtained.
4. This product performs best in thin bond gaps.
5. Very large thread sizes may create large gaps, which will
   affect cure speed and strength.
6. For maximum pressure and solvent resistance, allow at
   least 24 hours for the product to fully cure before filling
   and pressurizing system.
7. This product is designed to give controlled friction
   (torque/tension ratio), during assembly.

FOR CLEANUP

1. Wipe off any material outside the joint with a dry cloth.
2. Clean hands with Permatex Fast Orange® hand cleaner
   or soap and water.
3. Cured material must be removed with Permatex Gasket
   Remover.

TYPICAL CURING PERFORMANCE

Cure speed vs. temperature

The rate of cure will depend on the ambient temperature. Full
cure is attainable in 24 hours at room temperature, 72F
(22C), or 1 hour at 200F (93C).

Cure speed vs. substrate

The rate of cure will depend on the material used. Permatex
High Performance Thread Sealant will react faster and
stronger with Active Metals. However, Inactive Metals will
require the use of an activator (Surface Prep) to obtain
maximum strength and cure speed at room temperature.

Cure speed vs. activator

Where cure speed is unacceptably long, or large gaps are present, applying an activator (Surface Prep) to the surface will improve cure speed. Assemblies will fully cure in 24 hours with activator.

GENERAL INFORMATION

This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).

STORAGE

Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 46F and 82F (8C and 28C) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container.
SDS
TDS

For More PERMATEX products